Attempting to set mild steel rivets larger than 1/8”diameter or any rivet made of hardened material will bend the frame on this andall clamp style rivet tools. Important Note:Tubular andSemi-Tubular rivets larger than 1/8” diameter must be made of soft metal suchas Aluminum or Copper. Additional die sets are available from Hanson Rivet. As your needs change you can expand the range of your "THIRD HAND RIVET TOOL"simply by switching the dies.Other clamp style rivet toolscan’t do that. The “THIRDHAND RIVET TOOL” uses the same hardened-steel rivet squeezerdies found in professional rivet setting equipment.With the included dieset it will neatly roll clinch 1/8” diameter tubular or semi-tubular rivets1/8” to 1” long and up to 2-3/8” in from the edge of the work-perfect for Tonkaand Pinball restoration.These high-quality Hanson brand dies arereversible in the tool allowing you to install the rivet with the head insideor outside the work-whichever suits your application.Bolt itupright on your workbench, screw it vertically or horizontally to a post, clampit in a vise or use it handheld-whichever works best for the job.Areinforced mounting hole is there when you need it. The “THIRDHAND RIVET TOOL” can be mounted to any surface giving you awelcome “third hand” during the assembly and riveting process.Thethreaded die drivers provide precise control while clinching the rivet-animportant advantage when working with fragile materials that could easily bedamaged using punch or pliers style rivet tools. The “THIRDHAND RIVET TOOL” comes with two die drivers-a balanced and convenientT-handle driver that can be spun in the tool for speed, and a compact hex headdriver which provides more torque when needed and allows the tool to be used intight spaces where the swing of the T-handle would strike the work.Check out these great features to see why itremains the best choice: The "THIRDHAND RIVET TOOL" is the original tool of this type and hassold on since 2010. Uses include Tonka, Pinball, Vintage Bikes, Classic Cars,Metalwork, Jewelry and more. This hefty little guy is simple to use and will giveconsistent, professional results in a variety of repair, restoration andfabrication projects. The "THIRDHAND RIVET TOOL" is your solution to accurate, affordabletubular rivet setting. Don’t wait - this could be your last chance to own one of these greatrivet tools! I located a supplyof “new old stock” clamps and will offer the “THIRD HAND RIVET TOOL” until theyare gone. TUBULAR RIVET TOOL + 1/8 DIE SET + RIVETS = PERFECT FOR TONKA PINBALL TOY REPAIR:Īvailable again for a limited timeonly! Pony® brand clamps are nolonger made and that makes this tool difficult to produce. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network. When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. I was contemplating this one which looks more portable:Įbay.com link: Chain Breaker Cutter Master Link Removal Riveter Riveting Press Tool HDīut I think I will try what you advised.TUBULAR RIVET TOOL + 1/8 DIE SET + RIVETS = PERFECT FOR TONKA PINBALL TOY REPAIR Thanks so much, this was a super valuable post to me! Thanks for all the advice Pinsiders, you guys are always so helpful, but I think this is what I will go with. The Pin Restore rivet kit also includes washers. Note that when ever you rivet where the bottom of the rivet would roll over against plastic that you must use a rivet washer. Pin Restore also sells a nice rivet starter kit ($30). I also have a rivet press, but there are times when the rivet press cannot reach a rivet. You can support the rivet head with a block of wood ( I like to use the jaws on my vise) then just use this tool to hammer against the bottom of the rivet. On the same Pin Restore site indicated above, if you scroll down below the rivet press, you will see a Rivet Roll Over punch ($25). There is a cheaper way to go that will work just as well as the press.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |